designed & dimensioned in millimeters do not scale from this print 3.00 (typ) 'a' see note 2 (see note 11) t/b bow see table 1 -z- r 0.20 (typ) "a" "d" 45 "c" 2.0 7.950 1.17 45 9.230 17.600 (typ) 15.200 20.000 5.060 "b" "b" "b" "k" "k" "d" "d" c l gate recess (see note 8) c1 a -x- 0.10 y z -y- 1.25 3.45 "e" "f" 2.032 "e" "e" "f" "f" 'h' 'j' "c" "c" "l" "l" 'g' c2 c3 cavity id (see note 3 & 4) c l c l a a s/s bow 0.06 a 0.328 15 1.49 0.91 0.751 1.800 detail 'a' scale 5 : 1 qem8-xxx-xx.x-dv-xx no of positions -020 (per row) lead style -02.0 = 2mm -05.0 = 5mm row specification -dv: double vertical no of banks -01 thru -03 fig.1 (qem8-020-02.0-dv-02 shown) a a a a a a a a * *= not engineering approved sheet of unless otherwise specified, dimensions are in millimeters tolerances are: decimals angles x.x: 0.3 2 x.xx: 0.08 x.xxx: 0.050 material: qem8 body by: qem8-xxx-xx.x-dv-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing clay w 9/11/2007 4 1 sheet scale: 2:1 f:\dwg\misc\mktg\qem8-xxx-xx.x-dv-xx-mkt.slddrw notes: 1. represents a critical dimension. 2. samtec logo shall appear at two equally spaced locations on surface shown and opposite surface, approximately 0.80 x 1.1 3. all multiple cavity molds shall identify each cavity with a number designation located where shown. 4. all identification marks must not stand greater than 0.05 off the surface of the part. 5. molded surfaces shall be consistent and smooth. surfaces to be free of scatches, nicks, sink areas, voids or other blemishes. 6. all draft must be within specified tolerances. 7. all dimensions symmetrical about centerline within 0.05, unless otherwise specified. 8. gate pad to be recessed 0.10 9. position 1 indicator to be recessed 0.10 10. no draft permissible on this surface. 11. t/b bow to be measured on both sides of part. 12. measure at the first and last position of each bank. max regrind: 50% max flash allowed: 0.08 max gate vestige: 0.08 c 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 vectra e130i color: black -02.0 sumika super e6007 lhf-mrb2 -05.0 revision a
r 0.35 (typ) 0.900 0.030 r 0.25 (typ) 1.50 r 0.08 (typ) 0.22 section "e"-"e" scale 6 : 1 c6 0.10 x y z 60 0.550 0.330 1.765 0.400 0.300 0.600 0.013 section "f"-"f" scale 10 : 1 c7 see note 10 0.05 w z 0.05 w z 0.06 x z -w- 0.05 w z 0.60 ref 1.765 4.67 ref 5.550 30 30 15 0.765 60 0.200 0.025 2.680 0.178 0.013 9.23 ref 3.31 0.90 0.30 1.16 1.250 1.405 0.97 0.250 30 0.60 0.150 0.010 0.19 r 0.50 0.048 0.020 section "b"-"b" scale 8 : 1 c l c4 c5 see note 10 see note 10 -y- 0.05 y z 0.05 y z 0.08 y z 0.05 y z 0.10 y z 0.250 0.75 (typ) 0.750 20 1.48 0.62 1.00 0.50 0.55 17.5000.025 3.00 (typ) 0.26 0.65 0.15 section "d"-"d" scale 3.5 : 1 c l 0.05 x 3.00 1.25 5.50 0.82 4.17 section "c"-"c" scale 5 : 1 c l sheet of qem8 body by: qem8-xxx-xx.x-dv-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing clay w 9/11/2007 4 2 sheet scale: 2:1 revision a f:\dwg\misc\mktg\qem8-xxx-xx.x-dv-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
45 1.60 0.46 3.1 (typ) 4.3 1.4 0.4 (typ) 3.4 0.75 r 1.1 3.2 1.8 r 0.35 1.050 0.900 0.030 0.750 0.40 detail 'h' scale 5 : 1 c10 0.10 x z 0.10 y z 1.8 3.2 3.1 (typ) 0.4 (typ) r 1.1 3.4 4.3 detail 'j' scale 5 : 1 3.19 r 0.20 (typ) 5.38 see note 12 30 9.230 (ref) 1.405 ref 4.665 5.765 5.50 see note 12 section "k"-"k" scale 6 : 1 c l c8 c9 a 0.10 y z 0.10 y z 1.20 2.00 2.60 section "l"-"l" scale 5 : 1 0.30 0.20 ref 0.35 (typ) r 0.44 (typ) r 0.10 (typ) detail 'g' scale 16 : 1 c l a sheet of qem8 body by: qem8-xxx-xx.x-dv-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing clay w 9/11/2007 4 3 sheet scale: 2:1 revision a f:\dwg\misc\mktg\qem8-xxx-xx.x-dv-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
"h" "g" "q" "q" 'p' "n" "n" fig.2 (qem8-020-05.0-dv-02 shown) (same as fig 1 except as shown) r 0.27 90 0.20 (typ) 0.80 (typ) detail 'p' scale 10 : 1 "m" "m" 4.00 section "m"-"m" scale 4 : 1 2.90 7.10 section "n"-"n" scale 4 : 1 4.06 3.40 0.45 "j" "k'" 3.750 0.25 section "q"-"q" scale 6 : 1 sheet of qem8 body by: qem8-xxx-xx.x-dv-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing clay w 9/11/2007 4 4 sheet scale: 2:1 revision a f:\dwg\misc\mktg\qem8-xxx-xx.x-dv-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|
